NOTICE FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. WARRANTY Shortcut Labs AB warrants that your Flic hardware product (“the product”) will be free from defects in materials and workmanship for a period of 24 months from the date of delivery to the original retail purchaser (“the warranty period”). Battery life will be shortened with heavy usage and/or use in extreme conditions.Do not submerge and do not use chemical or abrasive cleaning products. Do not use the product in temperatures below -20☌ or above +54 ☌.Do not attempt to service the product.As such they are not suitable for children or pets. They contain small parts and accessories that present a choking hazard. SAFETY USAGE GUIDELINES The Flic Hub and Flic are not toys. They can be found at Alternatively you can contact us via the in-app customer support or email us at COMPLIANCE Shortcut Labs declaration of conformity is available at For a full compliance list visit PROBLEMS If you have any further issues setting up or using your Hub and/or Flic buttons that are not answered here then please read through our full FAQ’s. This can be found on the label on the underside of your Hub. If you remove the Hub from your account and reconnect to it then you will be prompted to use the Factory Password when pairing. All your account settings will be lost and the Hub will return to default. This allows for the Hub to play a sound as feedback to know that a Flic button has been pressed.įACTORY RESET If, for any reason, you must perform a factory reset you need to press the pinhole button for between 10-15 seconds. Leave it to air-dry and it will return to full stickiness.ĪUDIO Connect the Flic Hub to any speaker via the 3.5mm audio jack connector.Remove it from the IR base and rinse with water.If the adhesive starts to loose its stickiness then you can clean it Once you have all your actions setup you can simply peel away the label and secure the IR blaster in the best location to serve all your devices. INFRARED ACCESSORY The Flic IR accessory uses the same reusable adhesive as the Flic button. To setup your first action simply select the IR Blaster action within the Flic app. For best results ensure clear line of sight between IR accessory and recieving device. INFRARED ACCESSORY Connect your Flic IR accessory to the Hub via the 2.5mm connector and place the IR blaster in general the direction of the recieving device(s). You can do this by tapping the gear (settings) icon and selecting the ‘Remove’ option. Alternatively, if you are pairing a Flic button that was previously paired to another device or Hub then you will need to remove it from that device first. You will be prompted to press the Flic button and the pairing should take a few seconds. PAIRING YOUR FLIC BUTTONS If you are pairing a brand new Flic button to the Hub for the first time then simply tap the ‘+’ button in the bottom right corner of the Hub app page. Look for the network settings section and press test. To check if the internet connection for the Hub is active you should open the Hub settings page. If the Hub doesn’t have an acitve internet connection you will not be able to connect any Flic buttons. Alternatively you can simply connect the Hub, via an ethernet cable, directly into your home router/network. INTERNET CONNECTION To connect the Hub to your Wifi network open the Flic App and follow the setup steps to get the Hub connected to the internet. If using an adaptor with less than the recommended current rating you may experience unstable behaviour. We recommend that you use an adapter can supply the Hub with at least 1A. Follow the setup and start connecting your Flic buttons. After approximately 60 seconds the LED will dim, indicating that it can now be found using the Flic App on your phone. The Hub will now turn on, indicated by a bright red LED. POWER Connect the Micro USB cable to the Hub and an external power adapter. A Flic button within Bluetooth range of the Hub The phone is only necessary during the setup process. An active internet connection (Wifi or Ethernet) 2. GETTING STARTED To get started make sure that you have: 1. USER MANUAL Flic Hub / Flic Hub LR English
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |